Controlador programable EBS 9 FET
EBS Programmable Controllers are technically complex products for experienced users. Please read this page carefully before asking your questions.
These well-proven and high-quality controllers are equipped with 9 MOS-FETs. Built-in high-quality components (MOS-FETs and ELKOS) provide greater longevity and less heat build-up. Programmable functions and compatibility to many hub motors offer a huge selection of applications. If you wish to select a setting different from standard, please choose in the drop down menu above.
In any case, always note the manufacturer's voltage and current specifications. Choosing inappropriate settings can damage the connected battery or motor. Ebike Solutions disclaims any liability for damages caused by an inappropriate configuration.
For programming a USB programming cable is required which is not included in the delivery. Further information for the programming of the controller can be found in the USB-programming cable's product pages. Inappropriate configuration can cause severe damages to the controller. Removing the seal from the controller voids warranty.
Instructions for use can be downloaded below.
Product details | cops01-9-48b | cops01-9-72b | copsl01-9-72b |
Hall sensor activation | yes | yes | no |
Cycle Analyst access | no | yes | yes |
Recuperation | optional | optional | optional |
Technical data | cops01-9-48b | cops01-9-72b | copsl01-9-72b |
standby power consumption | less than 1W | less than 1W | less than 1W |
Maximum voltage | 60V total | 90V total | 90V total |
Rated Voltage | 24-48V | 24-72V | 24-72V |
Continuous current | 500W 25A (at 36V) | 500W 25A (at 36V) | 500W 25A (at 36V) |
MOS-FET Type | IRFB3307 | IRFB4110 | IRFB4110 |
Controller (MCU) | - | - | - |
Weight including cables | approx. 440g | approx. 440g | approx. 440g |
Length | 121mm / 152mm including clips | 121mm / 152mm including clips | 121mm / 152mm including clips |
Width | 87mm | 87mm | 87mm |
Thickness | 45mm | 45mm | 45mm |
Programmed default settings | |||
Current limitation | approx. 25A | approx. 25A | approx. 25A |
Rated Voltage | 36V | 36V | 36V |
Low voltage switch-off | approx. 30V | approx. 30V | approx. 30V |
Steps | 50/75/100% | 50/75/100% | 50/75/100% |
Advice for customizing the controller
Low voltage switch-off and maximum current
For correct numbers for Ebike Solutions batteries, please refer to the respective product pages. For any products not made by us please contact the respective manufacturer.
Adjusting levels
The levels set a limit of a certain percentage of the maximum speed. These levels do not limit power output. As long as no levelled button is installed the system is automatically set to level 2. To use with 6-level display select 100/100/100%
The steps can be shifted from the controller by manually by-passing the cables.
Steps | Bridge between |
1 | black - red |
2 | none |
3 | black - green |
Recuperation (recycling energy)
Using a solder bridge and a special programming the controller can be prepared for recuperation. In order for recuperation to be actually possible a direct drive motor is mandatory. We can adjust recuperation to three levels: Weak for 16-18" wheels, medium for 20-24" wheels and powerful for 26-28" wheels. You can use the medium recuperation for 16-18" wheels to achieve a higher recuperation rate.
Technische Daten | cops02-9-48b | copsl02-9-48b |
Standby Stromverbrauch | unter 1W | unter 1W |
Maximale Spannung | 60V absolut | 60V absolut |
Nennspannung | 24-50,4V | 24-50,4V |
Dauerleistung Strom | 500W 25A (bei 36V) | 500W 25A (bei 36V) |
MOS-FET-Typ | IRFB3307 | IRFB3307 |
Gewicht mit Kabeln | ca. 440g | ca. 440g |
Länge | 121mm / 152mm mit Laschen | 121mm / 152mm mit Laschen |
Breite | 87mm | 87mm |
Höhe | 45mm | 45mm |
Steckerstandard | EPMS | EPMS |
voreingestellte Standardwerte | ||
Strombegrenzung | ca. 20A | ca. 20A |
Nennspannung | 36V | 36V |
Unterspannungsabschaltung | ca. 26V | ca. 26V |
Stufen | 50/75/100% | 50/75/100% |
für Motoren | mit Hallsensoren | ohne Hallsensoren |
Hinweise zur Anpassung des Controllers
Unterspannungsabschaltung und Maximalstrom
Die korrekten Werte für Akkus von Ebike Solutions finden Sie auf der jeweiligen Produktseite. Bei nicht von uns gefertigten Modellen wenden Sie sich bitte an den Hersteller.
Stufen anpassen
Die Stufen legen ein Geschwindigkeitslimit in Prozent der Maximalgeschwindigkeit fest. Die Stufen begrenzen nicht die Leistung. Wenn kein Stufenschalter angeschlossen ist, bleibt automatisch Stufe 2 eingestellt. Für den Betrieb mit einem 6-Stufen-Display wählen Sie 100/100/100%
Controllerseitig lassen sich die Stufen manuell durch Überbrücken der Kabel schalten:
Stufe | Brücke zwischen |
1 | schwarz - rot |
2 | keine |
3 | schwarz - grün |
Parametrierung des Controllers
Für die Programmierung wird ein USB-Programmierkabel benötigt, das nicht im Lieferumfang enthalten ist. Weitere Informationen zum Programmieren der Controller finden Sie auf den Produktseiten des USB-Programmierkabels. Durch falsche Programmierung können Schäden am Controller entstehen. Daher erlischt die Gewährleistung beim Entfernen der Versiegelung am Controller.
Informationen zur eigenständigen Parametrierung finden Sie hier:
Programmierkabel und Hinweise zur Parametrierung von cops-Controllern
- Montageanleitung EBS Programmierbarer Sensor-Controller 9 FET V1.3
- Montageanleitung EBS Programmierbarer Sensorlos-Controller 9 FET V2