EBS Programmable Control System with 12-FET controller

The EBS Programmable Control System is ideal for those who are familiar with technology and... more

The EBS Programmable Control System is ideal for those who are familiar with technology and prefer to perform their own programming.
Our reasonably priced offers the following advantages:

  • Custom voltage setting: 24/36/48V
  • Possible power-tuning by voltage
  • Connecting the Cycle Analyst (depends on controller)
  • Adjusting recuperation
  • When requested controls can be reduced to an absolute minimum.

Combine your existing motor and battery with the EBS Programmable Control System and build up your very own custom tailored electric bicycle for a reasonable price.



Controller

EBS programmable controller for sensor motors 12 FETThe EBS programmable controller is the control system's brain and can be customized according to your needs. A black aluminium housing protects the electronics from splash water and dissipates heat. The default setting is adjusted to provide support after half a revolution of the cranks. Simply choose your desired accessories and connect them; no matter if it's power throttle, brake kill switch or 6-level display: With our controller you stay flexible. You can actually use our controller for all our pedelec motors featuring hall sensors. Optionally we offer non-sensor controller at the same price. When ordering a controller please tell us in the information section.




Pedal Assist Sensor (PAS)

EBS cadence sensor V7 with 6-Magnet-discThe Pedal Assist Sensor (PAS) consists of a sensor with attachment clamp and a plastic disc housing 6 magnets. The magnet disc is placed on the bottom bracket axle and the sensor is attached to the bottom bracket cup using the clamp. As soon you start pedalling the magnets pass by the sensor. This signal is routed to the controller that activates the motor. To enable pedalling backwards is safe, our cadence sensors are equipped with additional hall sensors. This prevents the motor from accidentally being activated.







EBS 3-position switch

EBS 3-position switch

You keep simple control with the 3-position toggle switch. The 3-position switch's default setting is adjusted to 50%, 75% and 100% of maximum speed. This way you can always choose the desired level of support right from the handlebar. Different settings from 30 to 100% are available on request.












Versions of the Programmable Controller

EBS Programmable Controllers are technically complex products for experienced users. Please read this page carefully before asking your questions.

These well-proven and high-quality controllers are equipped with 6 MOS-FETs. Built-in high-quality components (MOS-FETs and ELKOS) provide greater longevity and less heat build-up. Programmable functions and compatibility to many hub motors offer a huge selection of applications. If you wish to select a setting different from standard, please choose in the drop down menu above.

In any case, always note the manufacturer's voltage and current specifications. Choosing inappropriate settings can damage the connected battery or motor. Ebike Solutions disclaims any liability for damages caused by an inappropriate configuration.

If you wish to program the controller on your own you will need a USB programming cable which is not included. Further information for the programming of the controller can be found in the USB-programming cable's product pages. Inappropriate configuration can cause severe damages to the controller. Removing the seal from the controller voids warranty.

Instructions for use can be downloaded below.


Product details cops01-12-48b cops01-12-72b copsl01-12-72b
Hall sensor activation yes yes no
Cycle Analyst access yes yes yes
Recuperation optional optional optional


Technical data cops01-12-48b cops01-12-72b copsl01-12-72b
standby power consumption less than 1W less than 1W less than 1W
Maximum voltage 60V total 90V total 90V total
Rated Voltage 24-48V 24-72V 24-72V
Continuous power 700W 30A (at 36V) 700W 30A (at 36V) 700W 30A (at 36V)
MOS-FET Type IRFB3307 IRFB4110 IRFB4110
Controller (MCU) GPM8F3108A GPM8F3108A GPM8F3108A
Weight including cables approx. 545g approx. 545g approx. 545g
length 149mm / 181mm including clips 149mm / 181mm including clips 149mm / 181mm including clips
width 87mm 87mm 87mm
thickness 45mm 45mm 45mm
programmed default settings  
Current limitation approx. 25A approx. 25A approx. 25A
Rated Voltage 36V 36V 36V
low voltage switch-off approx. 30V approx. 30V approx. 30V
Steps 50/75/100% 50/75/100% 50/75/100%


Advice for customizing the controller


Low voltage switch-off and maximum current

For correct numbers for Ebike Solutions batteries, please refer to the respective product pages. For any products not made by us please contact the respective manufacturer.


Adjusting levels

The levels set a limit of a certain percentage of the maximum speed. These levels do not limit power output. As long as no levelled button is installed the system is automatically set to level 2. To use with 6-level display select 100/100/100%

The steps can be shifted from the controller by manually by-passing the cables.

Steps Bridge between
1 black - red
2 none
3 black - green

Recuperation (recycling energy)

Using a solder bridge and a special programming the controller can be prepared for recuperation. In order for recuperation to be actually possible a direct drive motor is mandatory. We can adjust recuperation to three levels: Weak for 16-18" wheels, medium for 20-24" wheels and powerful for 26-28" wheels. You can use the medium recuperation for 16-18" wheels to achieve a higher recuperation rate.




In addition to the EBS Programmable Control System you need


EBS e-bike motor

In addition to the EBS Programmable Control System you need an EBS e-bike motor. Ebike Solution offers e-bike motors with different power levels.


36V or 48V battery

To use the EBS Programmable Control System you need a high-power e-bike battery.


Conversion and lacing with third party components (motor, battery)

Of course we can retrofit your bike with our EBS conitoring system using your existing motor and battery. Costs for the retrofitting and lacing will be individually calculated based on duration and compatibility of third-party components to our EBS products. Also we can perform possible modifications on third-party components for extra charge. Please keep in mind that customizations can increase labour time. We can also send you an estimate after prior consultation by phone.




Do you have any further questions?

This is a brief step-by-step introduction to conversion:

go to conversion advisor

FAQs and answers about our online shop, please click:

FAQs
Controller Der EBS Programmierbaren Steuersystems ist das Gehirn des Steuersystems und... more

Controller

EBS Programmierbarer Controller für Sensormotoren 12 FET Der EBS Programmierbaren Steuersystems ist das Gehirn des Steuersystems und kann durch eine individuelle Konfiguration Ihren Bedürfnissen entsprechend abgestimmt werden. Ein schwarzes Aluminiumgehäuse schützt die Elektronik vor Spritzwasser und leitet entstehende Wärme ab. Die Ansteuerung ist ab Werk so eingestellt, dass Sie nach etwa einer halben Kurbeldrehung unterstützt werden. Wählen Sie einfach das gewünschte Zubehör aus und schließen Sie es an; ob Gasgriff, Bremsabschalter oder 6-Stufen-Display: Mit unserem Controller bleiben Sie flexibel. Übrigens können Sie den Controller mit allen unseren Pedelec Motoren verwenden, die Hallsensoren haben. Wahlweise liefern wir einen sensorlosen Controller zum gleichen Preis. Bitte geben Sie den gewünschten Controller beim Bestellvorgang im Hinweisfeld an.




Pedal Assist Sensor (PAS)

EBS Tretsensor V7 mit 6-Magnet-Scheibe Der Tretsensor (PAS) besteht aus einem Sensor mit Schelle und einer Kunststoffscheibe mit 6 eingelassenen Magneten. Die Magnetscheibe wird auf die Kurbelachse gesteckt und der Sensor mit der Schelle an der Tretlagerschale befestigt. Sobald Sie in die Pedale treten, werden die Magneten am Sensor vorbeigeführt. Diese Information geht zum Controller, der den Motor ansteuert. Damit ein sicheres Rückwärtstreten möglich ist, haben unsere Tretsensoren zusätzlich 2 Hallsensoren. So wird verhindert, dass sich der Motor versehentlich dazu schaltet.







3-Stufen-Schalter

EBS 3-Stufen Schalter

Unkompliziert behalten Sie die Kontrolle mit dem 3-Stufen-Kippschalter. Die drei Stufen sind ab Werk auf 50%, 75% und 100% der maximalen Geschwindigkeit eingestellt. So können Sie jederzeit vom Lenker aus den gewünschten Unterstützungsgrad wählen. Andere Stufeneinstellungen zwischen 30-100% sind auf Anfrage möglich.










Technische Daten cops02-12-48b copsl02-12-48b Standby Stromverbrauch... more
Technische Daten cops02-12-48b copsl02-12-48b
Standby Stromverbrauch unter 1W unter 1W
Maximale Spannung 60V absolut 60V absolut
Nennspannung 24-50,4V 24-50,4V
Dauerleistung Strom 700W 30A (bei 36V) 700W 30A (bei 36V)
MOS-FET-Typ IRFB3307 IRFB3307
Controller (MCU) GPM8F3108A GPM8F3108A
Gewicht mit Kabeln ca. 545g ca. 545g
Länge 149mm / 181mm mit Laschen 149mm / 181mm mit Laschen
Breite 87mm 87mm
Höhe 45mm 45mm
Steckerstandard EPMS EPMS
voreingestellte Standardwerte  
Strombegrenzung ca. 25A ca. 25A
Nennspannung 36V 36V
Unterspannungsabschaltung ca. 26V ca. 26V
Stufen 50/75/100% 50/75/100%
für Motoren mit Hallsensoren ohne Hallsensoren
Hinweise zur Anpassung des Controllers Unterspannungsabschaltung und Maximalstrom Die... more

Hinweise zur Anpassung des Controllers

Unterspannungsabschaltung und Maximalstrom

Die korrekten Werte für Akkus von Ebike Solutions finden Sie auf der jewiligen Produktseite. Bei nicht von uns gefertigten Modellen wenden Sie sich bitte an den Hersteller.

Stufen anpassen

Die Stufen legen ein Geschwindigkeitslimit in Prozent der Maximalgeschwindigkeit fest. Die Stufen begrenzen nicht die Leistung. Wenn kein Stufenschalter angeschlossen ist, bleibt automatisch Stufe 2 eingestellt. Für den Betrieb mit einem 6-Stufen-Display wählen Sie 100/100/100%

Controllerseitig lassen sich die Stufen manuell durch Überbrücken der Kabel schalten:

Stufe Brücke zwischen
1 schwarz - rot
2 keine
3 schwarz - grün

 


 

Das benötigen Sie zusätzlich zum EBS Programmierbaren Steuersystem

EBS E-Bike Motor

Zu dem EBS Programmierbaren Steuersystem benötigen Sie einen Motor. Ebike Solutions bietet E-Bike Motoren in verschiedenen Stärken an.

36V oder 50,4V Akku

Zum Betrieb des EBS Programmierbaren Steuersystems benötigen Sie einen Hi-Power Ebike Akku.

Umbau und Einspeichen mit Fremdkomponenten (Motor, Akku)

Wir übernehmen für Sie gerne den Umbau Ihres Fahrrades mit unserem EBS Steuersystem und Ihrem bereits vorhandenen Motor und Akku. Die Kosten und die Dauer des Umbaus und des Einspeichens werden individuell berechnet und richten sich nach der Kompatibilität der Fremdkomponenten zu unseren EBS Produkten. Eventuelle Modifikationen an den Fremdkomponenten können wir für Sie gegen einen Aufpreis übernehmen. Bitte beachten Sie, dass sich die Umbauzeit durch individuelle Anpassungen verlängern kann. Einen Kostenvoranschlag können wir Ihnen nach vorheriger telefonischer Absprache zukommen lassen.

Rekuperation (Energierückgewinnung)

Mittels einer Lötbrücke und einer speziellen Programmierung kann der Controller für Rekuperation vorbereitet werden. Ob Sie letztlich rekuperieren können, hängt auch von dem verwendeten Motor ab, bei dem es sich um einen Direktläufer handeln muss. Wir können die Rekuperation kann in drei Stärken einstellen: schwach für 16-18", mittel für 20-24" und stark für 26-28" Räder. Sie können mittlere Rekuperation auch für 16-18" Räder verwenden, um eine stärkere Rückgewinnung zu erzielen.

Your Set Selection

Current Configuration
€36.90 *

Prices incl. VAT plus shipping costs

Select an article: Controller / Need help? +49 6221 871060

EBS Programmierbarer Controller für Sensormotoren 12 FET - bis 48V
EBS Programmierbarer Controller für Motoren ohne Hallsensoren 12 FET - bis 48V
Maxon MX Boost Motor Maxon MX Boost Motor
From €1,543.70 *
Last Viewed