EBS programmeerbare controller 9 FET

EBS Programmable Controllers are technically complex products for experienced users. Please read... altro

EBS Programmable Controllers are technically complex products for experienced users. Please read this page carefully before asking your questions.

These well-proven and high-quality controllers are equipped with 9 MOS-FETs. Built-in high-quality components (MOS-FETs and ELKOS) provide greater longevity and less heat build-up. Programmable functions and compatibility to many hub motors offer a huge selection of applications. If you wish to select a setting different from standard, please choose in the drop down menu above.

In any case, always note the manufacturer's voltage and current specifications. Choosing inappropriate settings can damage the connected battery or motor. Ebike Solutions disclaims any liability for damages caused by an inappropriate configuration.

For programming a USB programming cable is required which is not included in the delivery. Further information for the programming of the controller can be found in the USB-programming cable's product pages. Inappropriate configuration can cause severe damages to the controller. Removing the seal from the controller voids warranty.

Instructions for use can be downloaded below.


Product details cops01-9-48b cops01-9-72b copsl01-9-72b
Hall sensor activation yes yes no
Cycle Analyst access no
yes yes
Recuperation optional optional optional


Technical data cops01-9-48b cops01-9-72b copsl01-9-72b
standby power consumption less than 1W less than 1W less than 1W
Maximum voltage 60V total 90V total 90V total
Rated Voltage 24-48V 24-72V 24-72V
Continuous current 500W 25A (at 36V) 500W 25A (at 36V) 500W 25A (at 36V)
MOS-FET Type IRFB3307 IRFB4110 IRFB4110
Controller (MCU) - - -
Weight including cables approx. 440g approx. 440g approx. 440g
Length 121mm / 152mm including clips 121mm / 152mm including clips 121mm / 152mm including clips
Width 87mm 87mm 87mm
Thickness 45mm 45mm 45mm
Programmed default settings  
Current limitation approx. 25A approx. 25A approx. 25A
Rated Voltage 36V 36V 36V
Low voltage switch-off approx. 30V approx. 30V approx. 30V
Steps 50/75/100% 50/75/100% 50/75/100%


Advice for customizing the controller


Low voltage switch-off and maximum current

For correct numbers for Ebike Solutions batteries, please refer to the respective product pages. For any products not made by us please contact the respective manufacturer.


Adjusting levels

The levels set a limit of a certain percentage of the maximum speed. These levels do not limit power output. As long as no levelled button is installed the system is automatically set to level 2. To use with 6-level display select 100/100/100%

The steps can be shifted from the controller by manually by-passing the cables.

Steps Bridge between
1 black - red
2 none
3 black - green

Recuperation (recycling energy)

Using a solder bridge and a special programming the controller can be prepared for recuperation. In order for recuperation to be actually possible a direct drive motor is mandatory. We can adjust recuperation to three levels: Weak for 16-18" wheels, medium for 20-24" wheels and powerful for 26-28" wheels. You can use the medium recuperation for 16-18" wheels to achieve a higher recuperation rate.

Technische Daten cops02-9-48b copsl02-9-48b Standby Stromverbrauch... altro
Technische Daten cops02-9-48b copsl02-9-48b
Standby Stromverbrauch unter 1W unter 1W
Maximale Spannung 60V absolut 60V absolut
Nennspannung 24-50,4V 24-50,4V
Dauerleistung Strom 500W 25A (bei 36V) 500W 25A (bei 36V)
MOS-FET-Typ IRFB3307 IRFB3307
Gewicht mit Kabeln ca. 440g ca. 440g
Länge 121mm / 152mm mit Laschen 121mm / 152mm mit Laschen
Breite 87mm 87mm
Höhe 45mm 45mm
Steckerstandard EPMS EPMS
voreingestellte Standardwerte  
Strombegrenzung ca. 20A ca. 20A
Nennspannung 36V 36V
Unterspannungsabschaltung ca. 26V ca. 26V
Stufen 50/75/100% 50/75/100%
für Motoren mit Hallsensoren ohne Hallsensoren
Hinweise zur Anpassung des Controllers Unterspannungsabschaltung und Maximalstrom Die... altro

Hinweise zur Anpassung des Controllers

Unterspannungsabschaltung und Maximalstrom

Die korrekten Werte für Akkus von Ebike Solutions finden Sie auf der jeweiligen Produktseite. Bei nicht von uns gefertigten Modellen wenden Sie sich bitte an den Hersteller.

Stufen anpassen

Die Stufen legen ein Geschwindigkeitslimit in Prozent der Maximalgeschwindigkeit fest. Die Stufen begrenzen nicht die Leistung. Wenn kein Stufenschalter angeschlossen ist, bleibt automatisch Stufe 2 eingestellt. Für den Betrieb mit einem 6-Stufen-Display wählen Sie 100/100/100%

Controllerseitig lassen sich die Stufen manuell durch Überbrücken der Kabel schalten:

Stufe Brücke zwischen
1 schwarz - rot
2 keine
3 schwarz - grün

 

Parametrierung des Controllers

Für die Programmierung wird ein USB-Programmierkabel benötigt, das nicht im Lieferumfang enthalten ist. Weitere Informationen zum Programmieren der Controller finden Sie auf den Produktseiten des USB-Programmierkabels. Durch falsche Programmierung können Schäden am Controller entstehen. Daher erlischt die Gewährleistung beim Entfernen der Versiegelung am Controller.

Informationen zur eigenständigen Parametrierung finden Sie hier:
Programmierkabel und Hinweise zur Parametrierung von cops-Controllern

Verfügbare Downloads:

Ihre Set-Auswahl

Aktuelle Konfiguration:
0,00 € *

Prezzi incl. IVA più spese di spedizione

Wählen Sie einen Artikel aus: Controller / Sie haben Fragen? +49 6221 871060

EBS Programmierbarer Controller für Sensormotoren 9 FET - bis 48V
EBS Programmierbarer Controller für Motoren ohne Hallsensoren 9 FET - bis 48V
Visto