EBS Programmable Control System with 9-FET controller

The EBS Programmable Control System is ideal for those who are familiar with technology and prefer to perform their own programming.

Our reasonably priced offers the following advantages:

• Custom voltage setting: 24/36/48V
• Possible power-tuning by voltage
• Connecting the Cycle Analyst (depends on controller)
• Adjusting recuperation
• When requested controls can be reduced to an absolute minimum.

Combine your existing motor and battery with the EBS Programmable Control System and build up your very own custom tailored electric bicycle for a reasonable price.

Controller

The EBS programmable controller is the control system's brain and can be customized according to your needs. A black aluminium housing protects the electronics from splash water and dissipates heat. The default setting is adjusted to provide support after half a revolution of the cranks. Simply choose your desired accessories and connect them; no matter if it's power throttle, brake kill switch or 6-level display: With our controller you stay flexible. You can actually use our controller for all our pedelec motors featuring hall sensors. Optionally we offer non-sensor controller at the same price. When ordering a controller please tell us in the information section.

Pedal Assist Sensor (PAS)

The Pedal Assist Sensor (PAS) consists of a sensor with attachment clamp and a plastic disc housing 6 magnets. The magnet disc is placed on the bottom bracket axle and the sensor is attached to the bottom bracket cup using the clamp. As soon you start pedalling the magnets pass by the sensor. This signal is routed to the controller that activates the motor. To enable pedalling backwards is safe, our cadence sensors are equipped with additional hall sensors. This prevents the motor from accidentally being activated.

EBS 3-position switch

You keep simple control with the 3-position toggle switch. The 3-position switch's default setting is adjusted to 50%, 75% and 100% of maximum speed. This way you can always choose the desired level of support right from the handlebar. Different settings from 30 to 100% are available on request.

Versions of the Programmable Controller

EBS Programmable Controllers are technically complex products for experienced users. Please read this page carefully before asking your questions.

These well-proven and high-quality controllers are equipped with 6 MOS-FETs. Built-in high-quality components (MOS-FETs and ELKOS) provide greater longevity and less heat build-up. Programmable functions and compatibility to many hub motors offer a huge selection of applications. If you wish to select a setting different from standard, please choose in the drop down menu above.

In any case, always note the manufacturer's voltage and current specifications. Choosing inappropriate settings can damage the connected battery or motor. Ebike Solutions disclaims any liability for damages caused by an inappropriate configuration.

If you wish to program the controller on your own you will need a USB programming cable which is not included. Further information for the programming of the controller can be found in the USB-programming cable's product pages. Inappropriate configuration can cause severe damages to the controller. Removing the seal from the controller voids warranty.

Instructions for use can be downloaded below.

Advice for customizing the controller

Low voltage switch-off and maximum current

For correct numbers for Ebike Solutions batteries, please refer to the respective product pages. For any products not made by us please contact the respective manufacturer.

Adjusting levels

The levels set a limit of a certain percentage of the maximum speed. These levels do not limit power output. As long as no levelled button is installed the system is automatically set to level 2. To use with 6-level display select 100/100/100%

The steps can be shifted from the controller by manually by-passing the cables.

Recuperation (recycling energy)

Using a solder bridge and a special programming the controller can be prepared for recuperation. In order for recuperation to be actually possible a direct drive motor is mandatory. We can adjust recuperation to three levels: Weak for 16-18" wheels, medium for 20-24" wheels and powerful for 26-28" wheels. You can use the medium recuperation for 16-18" wheels to achieve a higher recuperation rate.

In addition to the EBS Programmable Control System you need

EBS Pedelec Motor

In addition to the EBS Programmable Control System you need an EBS e-bike motor. Ebike Solutions offers pedelec motors and e-bike motors.

• go to EBS Pedelec Motors
• go to EBS e-bike motors

36V or 48V battery

To use the EBS Programmable Control System you need a high-power e-bike battery.

• EBS Pedelec Batteries in various shapes and capacities
  

• EBS high-power e-bike batteries in various sizes and capacities

Conversion and lacing with third party components (motor, battery)

Of course we can retrofit your bike with our EBS conitoring system using your existing motor and battery. Costs for the retrofitting and lacing will be individually calculated based on duration and compatibility of third-party components to our EBS products. Also we can perform possible modifications on third-party components for extra charge. Please keep in mind that customizations can increase labour time. We can also send you an estimate after prior consultation by phone.

Do you have any further questions?

This is a brief step-by-step introduction to conversion:

go to conversion advisor

FAQs and answers about our online shop, please click: