Cycle Analyst 3.1

Da 149,00 € *

Prezzi incl. IVA più spese di spedizione

Version:

  • aeca04-dp
    • for systems with EBS Programmable Controllers
    • High-end measuring device with lots of display options
    • The Cycle Analyst with the largest information range.
    • with speed display
Vantaggi
  • Livraison gratuite dans l'UE à partir de €500
  • 45 jours droit de retour
  • Retours gratuits et faciles
Cycle Analyst is a computer gauge for pedelecs, e-bikes and other electric vehicles. Version 3.0... altro

Cycle Analyst is a computer gauge for pedelecs, e-bikes and other electric vehicles. Version 3.0 also enables using THUN bottom brackets with torque gauge. This way retrofitted e-bikes and pedelecs can make use of power-based support.

Assistance

Attention: Only for e-bike professionals. E-drive only works if set-up is correct. Detailed instructions only available in English at the time. For further information, please refer to the manufacturer's website or the talk pages in the Endless-Sphere-Forum . THUN bottom bracket available on request.


Cycle Analyst is also a full fledged bike computer. Cycle Analyst 3.0 - Direct Plugin

The 10x2.5cm screen can display the following data:

  • Volt (V), Watt (W) and Ampere (A): Instant data that allow to determine battery capacity and current and power supplied by the battery.
  • Ampere hours (Ah), Watt hours (Wh) Actual energy supplied by the battery since the last reset of the Cycle Analyst.
  • Speed, distance, elapsed time: Typical bike computer features, including average speed, maximum speed and odometer.
  • Recuperation, Wh/km: Additional range in% generated by recuperation and average energy consumption in Watt hours per kilometre are displayed.
  • Peak current: Display shows peak currents of the motor reverse currents by recuperation and minimum voltage of the battery pack.
  • Charging cycles and Ampere hours (Ah): Data about number of charging and recharging cycles and number of supplied Ampere hours.

In addition Cycle Analyst can override the signal from the power throttle and limit current to the motor.

  • Speed limiter: Speed can be limited to a specific maximum (some soldering necessary).
  • Current limitation: Limiting the number of Amperes charged by the battery protects battery from overcharging.
  • Low voltage switch-off: Low voltage switch-off protects your battery from damage by total discharge. Note: Battery must be disconnected when it reaches its under voltage limit.

Cycle Analyst 3.0 - Direct Plugin with speed sensor cable

The Cycle Analyst 3.0 - Direct Plugin with speed sensor cable can directly be connected to most of our controllers (please note the instructions on the controller's product pages). It gets the data to measure speed from the motor's hall sensors. Therefore you need a motor with functional hall sensors. In addition it features ports for Thun bottom bracket sensor, Cycle Lumenator and Cycle Analogger.

Note: Please note that any soldering work or any other modification performed on the hardware voids warranty.

Hilfestellung ACHTUNG: Nur für Ebike-Profis. Der Antrieb funktioniert nur nach korrekter... altro

Hilfestellung

ACHTUNG: Nur für Ebike-Profis. Der Antrieb funktioniert nur nach korrekter Einrichtung einwandfrei. Die umfangreiche Dokumentation ist momentan nur auf Englisch verfügbar. Bitte nutzen Sie für weitere Informationen die Webseite des Herstellers oder die umfangreichen Diskussionsseiten im Endless-Sphere-Forum . NCTE Lager sind auf Anfrage erhältlich.

Hinweis: Bitte beachten Sie, dass durch Lötarbeiten oder sonstige Modifikationen an der Hardware die Gewährleistung erlischt.

Verfügbare Downloads:
Freno a disco CONTEC CDR-1 180mm/203mm Freno a disco CONTEC CDR-1 180mm/203mm
Da 17,90 € * 27,20 € *
Cycle Analyst 2.4 Cycle Analyst 2.4
Da 125,00 € *
Visto